Tri-Band Home Router: GUI
The GUI tab offers the same configurations and settings as the Config tab with some additional features for access restrictions, ISP VLAN setup, port forwarding, DMZ access, administration, as well as router and network status. Make sure you click on the Save Settings button at the bottom to apply the new settings to the Home Router before going to any other tab.
In the Setup tab under the Basic Setup sub-tab, you can set the Internet Connection Type to either automatically obtain IP configurations with Automatic Configuration - DHCP, manually set IP configurations with Static IP, or setup the router to operate as either Wireless AP or Media Bridge. You can also set the LAN IP configurations and DHCP server settings under the Network Setup section.
In order to illustrate router operation in Media Bridge and Wireless AP modes, Packet Tracer has the following samples:
ISP Vlans sub-section of
Network Setup, allows you to configure VLANs for situation
when they are used by ISP providers for service delivery.
Packet Tracer comes with the following sample networks illustrating this feature:
On the Wireless tab under the Basic Wireless Settings sub-tab, the only settings you can change are the Network Name (SSID) and the Standard Channel for each radio band.
Under the Wireless Security sub-tab, you can set the Security Mode to Disabled, WEP, WPA Personal, WPA Enterprise, WPA2 Personal, or WPA2 Enterprise. Depending on the security mode that you select, you will need to enter a WEP key, pass phrase and encryption type for WPA/WPA2 Personal, or the RADIUS server IP address, shared secret, and encryption type for WPA/WPA2 Enterprise. The settings are also available for each radio band.
Under the Wireless MAC Filter sub-tab, you can setup a wireless MAC address filter list to permit or prevent wireless clients from accessing the wireless network. To setup the wireless MAC filter, set the wireless MAC filter to Enabled and then select whether you want the MAC filter to prevent the listed clients from accessing the wireless network or to permit only the listed clients from being able to access the wireless network. Afterwords, begin entering the MAC addresses of the clients that you want to include in the MAC filter and then click the Save Settings button.
On the Security tab, there are no additional viewable sub-tabs and there are no parameters that you can edit.
Access Restrictions Configuration
On the Access Restrictions tab under the Internet
Access Policy sub-tab, you can apply various access
restrictions policies on the connected hosts. To add a policy to the
router, first select a policy you would like to edit from the Access
Policy drop-down menu and then Enter a Policy Name
for the policy. Then, set the Status to Enabled.
Next, click on the Edit List button and enter the
host IP addresses you would like to apply the policy on in the List
of PCs dialog that shows up. After editing the list, click
on Save Settings and Close inside
the dialog. Back in the GUI, select Deny to restrict
all applications or select Allow for specific
application access restriction. If you select Allow,
you can choose up to three applications to block. To block an
application, select the application from the Applications
list and click on the >> button to add it to
the Blocked List. To unblock an application, select
the application from the Blocked List and click on the <<
button. If you want to remove a policy, select the policy from the
Access Policy drop-down menu and click Delete
This Entry. The restrictions configured on this page can
also be applied on schedule by setting from and to
times of the day in the Schedule sub-section of the page. Time values
refer to the Environment clock displayed in the top -right
corner of the application's main window. Using this feature allows
for all configured restrictions to take place only within the time
Applications & Gaming Configuration
In the Applications & Gaming tab under the Single Port Forwarding sub-tab, you can forward packets destined to specific ports to an IP Address. To forward a port, select the appropriate application under the Application Name drop-down menu, enter the IP Address under the To IP Address column to which you want the packets to be forwarded, and then click on the box under the Enabled column. To forward a custom port, enter an application name and then enter the appropriate Externet Port, Internet Port, and Protocol. The Externet Port is the port to which the router will listen from the WAN side. The Internet Port is the port on your local server to which the router will forward packets.
Under the DMZ sub-tab, you can set a specific host to have DMZ access. To do so, click on Enabled to enable the DMZ feature and then enter the IP address of the host you want to have DMZ access.
In the Administration tab under the Management sub-tab, you can change the default password to access the router through the Web Configuration using the Web Browser and toggle Remote Management. In addition to this, if you are logged in using the Web Configuration, you can Backup and Restore Configurations.
Under the Factory Defaults sub-tab, the only available feature is Restore Factory Defaults. This will reset the configuration back to default settings.
Under the Firmware Upgrade sub-tab, you can upgrade the firmware of the Home Router. To upgrade the firmware, click on Browse, select a valid firmware image from the dialog that shows up, and then click OK. Once you have selected a firmware, click on the Start to Upgrade button to upgrade the firmware.
On the Status tab under the Router sub-tab, you can view Router Information and Internet Connection configurations. You can Release and Renew the IP address of the Internet port.
Under the Local Network sub-tab, you can view the Local Network and DHCP Server configuration. You can view the DHCP Client Table as well.
Under the Wireless Network sub-tab, you can view the various wireless configurations on the router.